2013 jeep wrangler thermostat




2013 jeep wrangler thermostat

Article Navigation:
  • Photo
  • Thermostats & Parts for Jeep Wrangler | eBay
  • Video
  • RELATED PAGES
  • Blog» Jeep JK L V6 thermostat housing replacement and if you drive a MY and newer Jeep Wrangler you need an OAT (Organic.

    Buy Thermostat Housing & Thermostat Fits Jeep Wrangler JK w/ L Engine Oil Filter Housing Cooler Adapter for Jeep Wrangler.

    RockAuto ships auto parts and body parts from over manufacturers to customers' doors worldwide, all at warehouse prices. Easy to use parts catalog.

    2013 jeep wrangler thermostat

    2013 jeep wrangler thermostat

    Once the engine reaches correct temperature, the thermostat opens and the coolant level will typically drop quite a bit. It will probably be difficult to get this coolant into the bucket below, which is why I had another drain pan on the ground. Brand Rukse Item Weight 5. The procedure for Jeep JK thermostat housing replacement is the same for either type of coolant though. December 11, azoffroading.

    2013 jeep wrangler thermostat

    2013 jeep wrangler thermostat

    2013 jeep wrangler thermostat

    2013 jeep wrangler thermostat

    2013 jeep wrangler thermostat

    P Code Engine Thermostat Replacement L

    This post is my attempt to describe the process of replacing a thermostat housing on a Jeep JK with a 3. When the coolant temperature reaches the specified opening point of the thermostat, it opens. Coolant will then flow through the radiator to keep the engine at a temperature close to the rated temperature of the thermostat.

    When I got home I plugged in my Flashcal to read the code. It was a p code an indication of a faulty thermostat or ECT — engine coolant temp sensor. Read this post before proceeding any further!

    2013 jeep wrangler thermostat

    The procedure for Jeep JK thermostat housing replacement is the same for either type of coolant though. Also if you buy concentrated coolant, you need to get a gallon of distilled water to mix it with, before adding it into your cooling system. If you plan on doing a full flush of your cooling system, make sure you have enough fresh coolant before you start.

    I believe the entire system uses about 3. Like I always mention I am not a professional mechanic, I just try to do as much work on my Jeep as possible. It helps me learn more about my vehicle and save some money that can be spent on parts and upgrades. I take no responsibility for any injury or breakage which might occur if you decide to follow these steps.

    2013 jeep wrangler thermostat

    Ratcheting socket wrench with a 10mm socket 2. T30 torx socket with short extension 4. Empty 1-gallon jug 6. Flathead screw driver 7. Clean shop rags 9. Plastic scraper if need be Flashlight or head lamp. Make sure you are parked on level ground and you let the engine cool down.

    Open your hood and remove the engine cover. Using your socket wrench and 10mm socket, remove the two bolts holding down the air intake plumbing between the air box and the throttle. Then using your flathead screwdriver, loosen the hose-clamps at the airbox and the throttle. Also pop out the thin radiator overflow hose from the clips near where the 10mm bolts come out. This small hose stays in place, but just needs to be removed from the clips.

    Disconnect the air temperature sensor on the bottom-side of air intake hose. With a better view of the sensor I was able to squeeze the little tab on the plug and disconnect the sensor with no problem.

    2013 jeep wrangler thermostat

    With the intake plumbing removed you will have much better view of the thermostat housing and an easy access to it. Find yourself one of these skinny 1 gallon plastic jugs and cut the top off. Put a drip tray and maybe some towels or cardboard too on the ground underneath and place the plastic jug just under the upper radiator hose clamp that secures it to the thermostat housing.

    Take off the radiator cap to relieve any pressure that might be in the cooling system. To limit the mess of coolant draining out of the upper radiator hose when you detach it from the thermostat housing, you can drain the coolant from the radiator at this point. You can drain the coolant using the radiator draincock located on the bottom of the radiator just below the filler neck.

    Thermostat Housing Replace and Bleeding Air from Cooling System - 2015 Jeep Wrangler JK 3.6L



    • Подписаться по RSSRSS
    • Поделиться VkontakteVkontakte
    • Поделиться на FacebookFacebook
    • Твитнуть!Twitter

    Leave a Reply

    Return to Top ▲TOP ▲