Toyota tacoma timing belt replacement interval




Toyota tacoma timing belt replacement interval

Article Navigation:
  • Photo
  • 5VZ-FE timing belt replacement interval? | Tacoma World
  • Video
  • RELATED PAGES
  • Get your timing belt repaired or replaced at Titus Will Toyota in Tacoma, WA. If your vehicle is in need of a timing belt service, you can easily schedule an.

    The average cost for a Toyota Tacoma timing belt replacement is between $ and $ Labor costs are estimated between $ and $ while parts are.

    Toyota Tacoma Forum 5VZ-FE engines say you should replace the timing belt at The original / scheduled maintenance guide simply carried over the 60, mile timing belt replacement interval.

    Toyota tacoma timing belt replacement interval

    Toyota tacoma timing belt replacement interval

    Toyota is one of the most dependable, long-lasting brands on the market. The pump uses Form In Place Gasket FIPG material that may make it difficult to remove, be sure that any prying you do will not damage the gasket surface. I found an earlier FSM that has ft. An interference engine should be carefully inspected before a broken timing belt is replaced because it may have sustained damage that will have to be repaired prior to installing a new belt.

    Toyota tacoma timing belt replacement interval

    Toyota tacoma timing belt replacement interval

    Toyota tacoma timing belt replacement interval

    Toyota tacoma timing belt replacement interval

    Toyota tacoma timing belt replacement interval

    Toyota Maintenance: L V6 Timing Belt Replacement

    The timing belt found in 1st generation Tacomas, 3rd generation 4Runners, and T Pickups require periodic replacement. From what I understand, belts on earlier models need to be replaced at 60, miles, and newer models at 90, miles. The purpose of this article is to point out the many steps that may be omitted in a routine belt change, and to show the use of an aftermarket service tool made by SnapOn and other companies.

    It follows the format of the Factory Service Manual FSM , but I can't guarantee it's applicability for your particular vehicle or model year. Even though I haven't performed this service myself, I was fortunate to observe one of our readers performing it on his supercharged Tacoma. To do this successfully at home you will need an assortment of hand tools, a foot pound torque wrench, Snap-On tool number YA, a special tool to hold the crankshaft pulley, help from a friend, and considerable experience working on vehicles.

    Toyota tacoma timing belt replacement interval

    Of course, make sure the radiator is cool to the touch before draining! Also remove the radiator cap. If you plan on replacing the water pump, you might as well remove the lower hose from the thermostat housing also. We didn't perform either of these two steps. Next, remove the PS drive belt by first loosening the adjuster clamp nut, then backing off the adjuster itself.

    Once it's loose, go ahead and unbolt the adjuster bracket from the water pump housing, and move the pump away from the engine. The reason for the removal is to gain access to the timing belt tensioner. By using the special Snap-On tool, we'll avoid having to unbolt the compressor from the engine. On supercharged V6s, first remove the oil dipstick and dipstick tube by unbolting it from the engine. If replacing the water pump, the whole tensioner assembly can be removed now.

    Toyota tacoma timing belt replacement interval

    The bottom section is held on with two clips. Instead of separating the two pieces, remove the fan first, then just remove four bolts and take out the whole shroud. Once removed, the tensioner then has to be compressed in a vise, pinned in the compressed state, and re-installed that way.

    Block the hole from the dipstick tube so coolant doesn't get into the crankcase if you are replacing the water pump. Remove six bolts around the cover. Disconnect the camshaft position sensor connector by pinching the locking tab. Then twist the connector to release it from the cover. After the timing belt cover is removed, inspect below and behind the camshaft timing pulleys for any leakage from the seals. You want to discover this before going any further, since their replacement is beyond the scope of this article.

    This is rare, but the possibility should not be overlooked. Remember to also inspect the idler and tensioner pulleys for any leakage or worn bearings as components are removed in the steps that follow.

    Toyota tacoma timing belt replacement interval

    While removing this, note which side goes against the belt the rounded or convex side. Turn the crankshaft always clockwise until it aligns with the mark behind it, and the two camshaft pulleys align with the marks behind them on top.

    If the camshaft pulleys are not aligned, turn the crankshaft one more revolution. Remove the pulley bolt when finished. If the marks are gone, be sure to apply new ones before removing the belt. This step was omitted. We were replacing the belt, so the old one was just cut off. If you are reusing the belt, remove the top center pulley first to make the belt slack. This entire step can be omitted if you're using the Snap On Tensioner Compressor. The aftermarket tensioner compressor only works if the old belt is removed.

    Toyota Tacoma 3.4 engine Timing belt - part 1 of 2



    • Подписаться по RSSRSS
    • Поделиться VkontakteVkontakte
    • Поделиться на FacebookFacebook
    • Твитнуть!Twitter

    Leave a Reply

    Return to Top ▲TOP ▲