How to change battery in mazda cx 5 key




How to change battery in mazda cx 5 key

Article Navigation:
  • Photo
  • How do you change the battery & program a Mazda CX-5 key fob? - FAQ | CarsGuide
  • Video
  • RELATED PAGES
  • The Mazda CX-5 key fob is needed to lock, unlock, and start the vehicle. Unfortunately it doesn't give you any low battery warnings. Luckily, replacing the battery.

    Replacing the battery at an Authorized Mazda Dealer is recommended to prevent damage to the key. If replacing the battery by yourself, follow the instruction.

    Fact! Initially, Mazda was called Toyo Kogyo. Rebranding was held not so long ago, in 1984. The name is taken in honor of Zoroastrian wisdom god Ahura Mazda.

    Jan 5, Learn How to Open Your Mazda Key to Replace a Dead Battery Like any battery, the battery in your Mazda's key fob could go dead, requiring.

    How to change battery in mazda cx 5 key

    How to change battery in mazda cx 5 key

    Remove the metal ignition key and set it aside in a safe place. The KEY indicator light green flashes in the instrument cluster for about 30 seconds after the engine is turned off for vehicles with a type A instrument cluster Search , messages are displayed in the instrument cluster. Dispose of used batteries according to the following instructions. There is the danger of explosion if the battery is not correctly replaced. Owner Maintenance Owner Maintenance Precautions.

    How to change battery in mazda cx 5 key

    How to change battery in mazda cx 5 key

    How to change battery in mazda cx 5 key

    How to change battery in mazda cx 5 key

    How to change battery in mazda cx 5 key

    Replace the Key Fob Battery on a Mazda CX-5

    A replacement coin cell A. The only tool needed to replace the battery is a small flathead screwdriver used to pry apart the key fob.

    Then turn over the key fob and located the small sliding tab. Slide the grey button towards the other side of the fob to release the emergency metal ignition key. Remove the metal ignition key and set it aside in a safe place. Insert the blade of your small flathead screwdriver in to the void A. Pull out the green circuit board remote control unit from the back half of the fob.

    How to change battery in mazda cx 5 key

    Gently pry apart the battery holder tray from the rear cover of the fob. Do not use excessive force! Once the rectangular battery holder tray has been separated from the rear cover of the fob, turn it over to reveal the battery cap. Carefully pry out the old battery with the small flathead screwdriver. Try to avoid damaging the metal electrical contacts. Line up the rear cover of the fob over the battery tray.

    Place the green circuit board remote control unit over the battery tray with the metal electrical contacts on the bottom and the small grey plastic buttons facing up towards you. Gently snap together the two halves of the fob until they are flush at every edge.

    How to change battery in mazda cx 5 key

    Test the new battery by standing near your CX-5 and pressing the "Unlock" or "Lock" buttons. If the new battery is working properly, you should see the parking lights flash and hear the door locks opening or closing. If you found this guide to be helpful, please consider making a small donation by clicking on the PayPal. I am not a registered charity. Donations are not tax deductible. Please help support this website by shopping at Amazon.

    Back Of Smart Key Fob. Metal Ignition Key Release. Pry Apart Two Halves. The first two steps are to remove the key fob from your key ring and any other keys. Remove Remote Control Unit. Pry Apart Battery Holder. Separate the rear cover and front cover of the key fob. Pry Off Rear Fob Cover. You may need to re-insert your screwdriver in several locations to finally pry it apart. Pry Off Battery Cover.

    Gently Pry Out Old Battery. Gently pry off the round battery cover and set the cap aside in a safe place. Panasonic CR 3V. Insert New CR Battery. Push On Battery Cap.

    How to change battery in mazda cx 5 key

    Line Up Rear Cover. Line up the round battery cover and gently snap the cap back in to place. Snap On Battery Holder. Rear Cover Flush With Tray. Line Up Green Circuit Board. Gently snap together the battery holder tray and the back half of the fob. Pop Together Two Halves. Line up the rubber buttons and the front cover of the fob over the green circuit board. Re-Insert Metal Ignition Key. Test New Key Fob Battery. Slide in the back up metal ignition key until it clicks securely in to place.

    How To Replace A Battery In A Mazda Key Fob Remote Control



    • Подписаться по RSSRSS
    • Поделиться VkontakteVkontakte
    • Поделиться на FacebookFacebook
    • Твитнуть!Twitter

    Leave a Reply

    Return to Top ▲TOP ▲