Electric dryer adapter




Electric dryer adapter

Article Navigation:
  • Photo
  • 3 Prong to 4 Prong Dryer Adapter: 150CARS.COM
  • Video
  • RELATED PAGES
  • Buy products related to 3 prong to 4 prong dryer adapter products and see what MICTUNING 18" 50M/30F Heavy Duty Dogbone Electrical Adapter with.

    150CARS.COM: AC WORKS 30 Amp 4-Prong Dryer Wall Outlet Adapter (To 3- Prong 30A EATON WD Dryer Electrical Receptacle, V, 30 A, 3 Pole, 3 Wire .

    Your Selection: Part Type: Dryer Cord . 30 Amp 4-Prong P Dryer Plug to 50 Amp Volt Welder Adapter (NEMA . 10 3-Wire Electric Dryer Cord.

    Electric dryer adapter

    Electric dryer adapter

    You're very thorough and make this very easy to understand. You most definitely CAN change the cord, though - cords are readily available, it is a simple task and is quite legal and safe to change the cord out. This is used to identify particular browsers or devices when the access the service, and is used for security reasons. Is there an adapter for the new L style cord to fit into the straight prong outlet or replace the outlet itself? The white wires you reference could be supplying a neutral to the control electronics, the motor or some other function - if so they must be connected to the neutral on the cord in order to function.

    Electric dryer adapter

    Electric dryer adapter

    Electric dryer adapter

    Electric dryer adapter

    Electric dryer adapter

    4 Prong to 3 Prong Dryer Adapter: 150CARS.COM

    Dan has been a licensed, journey-level electrician for some 17 years. He has extensive experience in most areas of the electrical trade. You've just moved into your new home, the new drapes are up, and the washer and dryer are ready to be put into place.

    The dryer cord won't plug in—the dryer cord has four prongs, but the wall receptacle only has three holes! What's up with this? What's up is that in the National Electric Code instituted a change, requiring all new dryers and home dryer receptacles to have 4 prongs instead of the older 3-prong style.

    Electric dryer adapter

    That fourth prong is a ground wire and is there for better electrical safety. Now, it would be convenient if there was a dryer plug adapter that you could plug into that three-pronged receptacle so that you could plug your dryer into that —but there isn't. You will have to change the dryer cord to make it fit. A screwdriver and a pair of pliers will do the job, although some nut drivers would be nice. Now if the situation with your dryer cord and outlet is backwards from this—that is, you have a three-pronged cord and a four-pronged outlet—you are looking at the wrong article.

    Look at this article instead: Begin by unplugging the dryer. There is high voltage inside volts that can give you a very nasty shock, even kill you. Make sure there is no chance of this, by unplugging the dryer before proceeding any further. There will be some kind of connector holding the dryer cable to the wall of the dryer so that it doesn't pull out. The most common type is a clamp with two screws on the outside that can be tightened to squeeze the wire into place.

    Electric dryer adapter

    Loosen these screws so that the wire can slide out of the dryer. Remove the cover plate from the wire terminal block, exposing the wires inside. Note where each color of wire terminates. Normally, you will see a row of three terminal screws, with the red and black wires connected to the two outside screws, the white wire connected to the center screw, and the green wire connected to the frame of the dryer. Work the old wire out of the connector that holds it to the wall of the dryer, and set it aside for possible future use.

    You never know when you might move again, and Murphy's Law says that if you do, it will be back into a home with a four-prong dryer plug! Once the four-wire cord is removed, it is time to install the new three-wire cord and plug. Work the wire through the connector, but do not tighten it yet.

    The red and black wires go to the outer two terminals in the photo the dryer wires are black and blue and the white wire goes to the terminal in the center of the terminal block. While the red and black wires are interchangeable, the white wire is not; make sure it goes to the center terminal, where the old white wire was. Most three-wire cords do not have colored wires, so instead of matching colors, identify the wires using the relative position of the wires in the cord.

    Electric dryer adapter

    The center wire of the three will always go to the center white terminal; the outer two wires go to the outer terminals. The outer two wires can be interchanged, but never put the center wire of a flat, three-wire cord on anything but the center terminal.

    Your three-prong cord will not have a green ground wire. In place of that wire a ground strap or short piece of 10 wire preferably green must be installed. One end should go to where the green wire on the old cord went, and the other end to the terminal where the white wire went. Do not ignore this step! You must have a "jumper" of some kind, a wire or strap, installed between the dryer frame and the white wire.

    Are RV dog bones (30 to 15 amp adapters) safe?



    • Подписаться по RSSRSS
    • Поделиться VkontakteVkontakte
    • Поделиться на FacebookFacebook
    • Твитнуть!Twitter

    Leave a Reply

    Return to Top ▲TOP ▲